How to properly paint wheels

Post guides or links to external guides here
Post Reply
User avatar
Tony Z
Donor
Donor
Posts: 14992
Joined: Wed Sep 14, 2005 8:33 am
What model do you have?: 2.3L 69; 1302; P/Van
Location: Klipheuwel (near Durbanville), Cape Town or working at sea
Has thanked: 191 times
Been thanked: 487 times
South Africa

How to properly paint wheels

Post by Tony Z »

retrovan wrote: So a lot of threads have asked about how do you do wheels the correct way.

Well here is the the right way to do wheel refurbishment as per the "Old Toppies"

1st you send the rims out for sand blast.
Next you have the whole wheel powder coated with the colour you want the hub to be.
Then you mask off the hub, Make sure you drop the masking tape into the grove, before sticking it to the wheel, so that it sits right down in the grove, as shown here;-

Image

Image

You may have noticed that the powder coating will not go into the grove/ joint line, this is normal and will be sorted later.

Now paint the uncovered edge of the rim, making sure you spray right to the bottom as well as over the edge of the rim, as you do not want a white ring between your rim and tyre.

Image

Image

Image

When dry, remove the masking carefully, as it may still have some wet spots, and you do not want to smear the paint now.

Image

Image

You will find you land up with a terrible edge line, that looks like S#it, and bumps from the sandblasting and powder coating.

Fear not, that is where experience comes into play.......

You now take a syringe, fill it with the paint used on the wheel, and start applying it to the wheel.

Image

Image

Make sure you have a steady stream coming out, and make sure the tip of the syringe, stays on the painted edge, NOT the grove, as it will flow in by it self.

If you do not keep it on the painted edge, you will land up with high spots, and smears where you do not want them, then you have to start all over again.

Take it slow, and make sure you wipe the front of the syringe perfectly clean before coming over the rim, as one drop could spoil the whole show.

If you do not have it all covered, or you have messed up, go around again, with more paint, and make a new edge line higher up.

When you done, it should look like this.......

Image

Image

Image

Image

Thanks for looking

Herman


calooker
Donor
Donor
Posts: 4973
Joined: Wed Sep 14, 2005 9:24 am
What model do you have?: 77 SP
Location: Johannesburg
Has thanked: 4 times
Been thanked: 98 times
Contact:

Re: How to properly paint wheels

Post by calooker »

I have done many wheels, after sandblast and 1 coat of etch primer, I seal the joint/seam with quality paintable acrilic sealer, very simple, no fuss, smoothed out with your finger then paint, never had a wheel rust in that area.
For what it's worth, ignorance has no limits ......
User avatar
Hloni
Exhaust Pipe
Posts: 1538
Joined: Tue May 27, 2008 4:30 pm
What model do you have?: It was a '75.
Location: Sharonlea, Randburg
Has thanked: 14 times
Been thanked: 11 times

Re: How to properly paint wheels

Post by Hloni »

Thanks Tony for pulling this into here.

If one were to paint the wheels, NOT powdercoat, would one need a high-heat paint or a standard automotive paint will do? I'm looking at a 2 tone too - match body, so not a standard "chrome/alu/ finish.
"Volkswagen customers want a relationship with their cars. Names like The Thing, Beetle, Fox, and Rabbit support this" - Kerri Martin
3011
User avatar
Tony Z
Donor
Donor
Posts: 14992
Joined: Wed Sep 14, 2005 8:33 am
What model do you have?: 2.3L 69; 1302; P/Van
Location: Klipheuwel (near Durbanville), Cape Town or working at sea
Has thanked: 191 times
Been thanked: 487 times
South Africa

Re: How to properly paint wheels

Post by Tony Z »

@retrovan
User avatar
retrovan
Donor
Donor
Posts: 8709
Joined: Mon Feb 07, 2011 8:51 pm
What model do you have?: 52T1,68FB,72Bay,75FL
Location: Eich! no, in Jefferys Bay
Has thanked: 421 times
Been thanked: 539 times
Contact:
Netherlands

Re: How to properly paint wheels

Post by retrovan »

Hloni wrote: Sat Jun 10, 2017 4:47 pm Thanks Tony for pulling this into here.

If one were to paint the wheels, NOT powdercoat, would one need a high-heat paint or a standard automotive paint will do? I'm looking at a 2 tone too - match body, so not a standard "chrome/alu/ finish.
Hi Hloni,

A std auto paint will do, not as robust as Powder, but if applied with a etch primer, then base coat then clear coat, the wheel will be perfect.

just allow for the correct flash off between coats.

The only must is that you clear coat it to seal it from Dog Piss

Herman
1952 Split Beetle 1835cc
1968 Fastback 2Lt.type4
1972 Low Light Bay Panel Van 2Lt type 4
1975 Fleetline Panel Van 1914cc
2020 MeFusco Beetle Truck 2Lt type 4
1972 FT Hahn SP 1776 cc
User avatar
Hloni
Exhaust Pipe
Posts: 1538
Joined: Tue May 27, 2008 4:30 pm
What model do you have?: It was a '75.
Location: Sharonlea, Randburg
Has thanked: 14 times
Been thanked: 11 times

Re: How to properly paint wheels

Post by Hloni »

Will surely seal it. Thanks Retro!
"Volkswagen customers want a relationship with their cars. Names like The Thing, Beetle, Fox, and Rabbit support this" - Kerri Martin
3011
User avatar
bugspray
Floorpan
Posts: 3468
Joined: Thu Jun 26, 2008 4:18 pm
What model do you have?: 71 Westy + 74beetle
Facebook: http://m.facebook.com/profile.php?r0d306f00&refid=7
Location: Pretoria- beetle / Benoni - Bus
Has thanked: 24 times
Been thanked: 16 times
South Africa

Re: How to properly paint wheels

Post by bugspray »

Yessss clear coat!! Redid a set of rossies but wanted a satin look. 2k satin black was used without a clear coat too keep the satin look.

Paint scratched like a mofo! Have to find satin clear or a Matt clear and redo now
Image
More than meets the eye!
User avatar
RebeccaB
Drip
Posts: 8
Joined: Mon Oct 12, 2020 11:02 pm
What model do you have?: 1973 Jurgens Autovil
Location: Cape Town
Has thanked: 10 times
Contact:
South Africa

Re: How to properly paint wheels

Post by RebeccaB »

excellent post. thank you.

where do I get my Wheels sandblasted and painted in Cape Town or nearby? and how much will it approx cost?

Thank you
73type2
Pushrod
Posts: 987
Joined: Fri Apr 21, 2017 11:37 am
What model do you have?: '73 T2 Single Cab
Location: Cape Town
Has thanked: 141 times
Been thanked: 100 times
France

Re: How to properly paint wheels

Post by 73type2 »

There are a couple of places close to you, e. g. Powder Coating World, Link Close, Montague Gardens.
73type2
Pushrod
Posts: 987
Joined: Fri Apr 21, 2017 11:37 am
What model do you have?: '73 T2 Single Cab
Location: Cape Town
Has thanked: 141 times
Been thanked: 100 times
France

Re: How to properly paint wheels

Post by 73type2 »

A couple of years ago I paid R450 per rim sandblasted and powder coated.
Post Reply