IS THIS A 1700 OR 1800 CONROD

Post by **Cyndi Kritzinger** » Sun Aug 09, 2020 2:03 pm

HOWDY ALL.

I AM TRYING TO DETERMINE IF THIS IS A 1700 OR 1800 CONROD.
I AM NOT LOOKING FOR GUESSES IF YOU DON'T MIND. 61.9 KB WhatsApp Image 2020-08-09 at 13.48.46.jpeg Check Error

Edmond · Post by **Edmond** » Sun Aug 09, 2020 8:13 pm

Looks like a 1700/1800 Conrod according to the Tom Wilson book

73type2 · Post by **73type2** » Mon Aug 10, 2020 8:42 am

I guess Edmond is not guessing...

sean · Post by **sean** » Tue Aug 11, 2020 1:49 pm

Hi Mark

What is the ID of the bush where the gudgeon pin goes through? You get 2 different 1700 rods that utilize different pistons.

Post by **Cyndi Kritzinger** » Tue Aug 11, 2020 4:08 pm

NO IDEA SEAN; I'LL HAVE TO MEASURE.
I ASSUME FROM YOUR QUESTION THAT THIS IS INDEED A 1700 CONROD THOUGH......
WHAT IS THE DIFFERENCE IN THE PISTONS AND WHY?

sean · Post by **sean** » Thu Aug 13, 2020 9:33 pm

Cyndi Kritzinger wrote: ↑Tue Aug 11, 2020 4:08 pm NO IDEA SEAN; I'LL HAVE TO MEASURE.
I ASSUME FROM YOUR QUESTION THAT THIS IS INDEED A 1700 CONROD THOUGH......
WHAT IS THE DIFFERENCE IN THE PISTONS AND WHY?

That appears to be a 1700, but it’s only based on a picture. Measure it to know properly.

Post by **Cyndi Kritzinger** » Thu Aug 20, 2020 6:03 pm

@ SEAN.... AND ANYONE ELSE THAT KNOWS THEIR STUFF.
CENTER TO CENTER 12.5CM (125MM)
COMPLETE LENGTH TOP OF NIPPLE TO BOTTOM OF CONROD 19.5CM (195MM)

Post by **retrovan** » Thu Aug 20, 2020 10:29 pm

If you read the above explanation then you have the tall balancing pad (Square thing on top)

So you have the 1700 con rod

The 1800 has a small bump balancing pad on top, as per photo, which you have not got.

OMO
Herman

sean · Post by **sean** » Tue Aug 25, 2020 3:35 am

Here is a pic below of 3 different rods I’ve taken. 1.7, 1.8 and 2.0.

Post by **Cyndi Kritzinger** » Tue Aug 25, 2020 1:20 pm

I'M FAIRLY SURE MINE IS A 1700 BUT THE ENGINE/BITS WAS/WERE SOLD TO ME AS AN 1800, HENCE THE UNCERTAINTY.
I DO REALISE THAT A LOT OF PEOPLE DON'T KNOW TOO MUCH ABOUT THESE THINGS.

Post by **retrovan** » Tue Aug 25, 2020 6:43 pm

As most books will only give you a guide, you will have to measure and measure and measure to make sure you have the right collection of parts to fit into one engine.

As so may hodgepodge motor's are out there with a mix and match parts list, you can not be sure what you have without measuring.

Good luck old boy.

Herman

Aircooled VW South Africa

IS THIS A 1700 OR 1800 CONROD

IS THIS A 1700 OR 1800 CONROD

Re: IS THIS A 1700 OR 1800 CONROD

Re: IS THIS A 1700 OR 1800 CONROD

Re: IS THIS A 1700 OR 1800 CONROD

Re: IS THIS A 1700 OR 1800 CONROD

Re: IS THIS A 1700 OR 1800 CONROD

Re: IS THIS A 1700 OR 1800 CONROD

Re: IS THIS A 1700 OR 1800 CONROD

Re: IS THIS A 1700 OR 1800 CONROD

Re: IS THIS A 1700 OR 1800 CONROD

Re: IS THIS A 1700 OR 1800 CONROD